Deutz-Fahr Series 5 D TTV

Coolant capacity & service interval

Deutz-Fahr Series 5 D TTV uses coolant with a capacity of 12 liters. Service intervals include checks every 10 hours and changes every 2400 hours or 24 months. The data covers 8 configurations.

The configuration chart below lists fill volumes and service intervals for each engine and trim variant.

TypeSpecifications
5090 D TTV, Stage 3B->ZKDET60200TD50001 (2021- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 2400 hours/ 24 months
5090.4 D TTV, Stage 3B->ZKDEU40200TD50001 (2021- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 2400 hours/ 24 months
5095 D TTV, Stage 5->ZKDHU70200TD50001 (2021- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 2400 hours/ 24 months
5100 D TTV, Stage 3B->ZKDEU00200TD50001 (2021- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 2400 hours/ 24 months
5100.4 D TTV, Stage 3B->ZKDEU80200TD50001 (2021- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 2400 hours/ 24 months
5105 D TTV, Stage 5->ZKDHU80200TD50001 (2021- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 2400 hours/ 24 months
5110.4 D TTV, Stage 3B->ZKDEV20200TD50001 (2021- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 2400 hours/ 24 months
5115 D TTV, Stage 5->ZKDHU90200TD50001 (2021- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 2400 hours/ 24 months

Additional Notes

  • All eight configurations of the Deutz-Fahr Series 5 D TTV covered in these specifications share an identical cooling system capacity of 12 liters, indicating a uniform engine cooling architecture across the lineup regardless of power output or emissions stage.
  • The 12-liter figure represents the total cooling system fill volume, which accounts for the radiator, engine block passages, hoses, and expansion reservoir combined rather than the engine block alone.
  • A coolant level check interval of 10 hours applies to all listed configurations under normal use conditions. In agricultural machinery, a 10-hour check interval corresponds roughly to daily inspection during active field seasons, reflecting the high thermal loads typical of tractor operation.
  • The coolant change interval is set at 2400 hours or 24 months, whichever comes first, across all configurations under normal use. The dual-trigger structure means time elapsed can mandate a change even when the hour threshold has not been reached, which is relevant for lower-utilization machines.
  • The specifications cover both Stage 3B and Stage 5 emissions variants. Stage 3B and Stage 5 refer to European non-road mobile machinery emissions standards, with Stage 5 representing a stricter tier that typically incorporates additional aftertreatment components. Despite this hardware difference, the cooling system capacity and service intervals are identical across both emissions stages in these specifications.
  • The Stage 3B variants include the 5090 D TTV, 5090.4 D TTV, 5100 D TTV, 5100.4 D TTV, and 5110.4 D TTV, while the Stage 5 variants include the 5095 D TTV, 5105 D TTV, and 5115 D TTV. The ".4" suffix in several model designations indicates a four-wheel-drive configuration, yet the cooling system specifications remain unchanged relative to their non-.4 counterparts.
  • Each configuration is identified by a unique serial number threshold, such as ZKDET60200TD50001 for the 5090 D TTV, indicating that the listed specifications apply from that serial number onward starting in 2021. Serial number thresholds of this kind are used to distinguish production batches that may have received specification or component updates.

Other Systems