Deutz-Fahr Series 3 E

Coolant capacity & service interval

Deutz-Fahr Series 3 E uses coolant with a capacity range of 4 to 12 liters. Service intervals include checking every 10 hours and changing every 1000 hours or 12 months, 1200 hours or 24 months, and 2000 hours or 24 months. The data covers 7 configurations.

The configuration chart below lists fill volumes and service intervals for each engine and trim variant.

TypeSpecifications
3045 E, Stage 5 ->NNZMW002V0BD50001 (2024- )
  • Use: Normal
  • Capacity 12 liter
  • Change 2000 hours/ 24 months
3050 E, Stage 5 ->NNZMW102V0BD50001 (2024- )
  • Use: Normal
  • Capacity 12 liter
  • Change 2000 hours/ 24 months
3055 E, Stage 5 ->NNZMW202V0BD50001 (2024- )
  • Use: Normal
  • Capacity 12 liter
  • Change 2000 hours/ 24 months
3065 E, Stage 5 ->NNZMW202V0BD50001 (2024- )
  • Use: Normal
  • Capacity 12 liter
  • Change 2000 hours/ 24 months
3035 E (2014- )
  • Use: Normal
  • Capacity 4 liter
  • Change 1000 hours/ 12 months
3045 E (2014- )
  • Use: Normal
  • Capacity 4 liter
  • Change 1000 hours/ 12 months
3065 E (2014- )
  • Use: Normal
  • Capacity 12 liter
  • Check 10 hours
  • Change 1200 hours/ 24 months

Additional Notes

  • The Deutz-Fahr Series 3 E cooling system capacities split into two distinct groups across the lineup. The 3035 E and the pre-Stage 5 3045 E hold 4 liters, while the 3065 E and all Stage 5 variants across the 3045 E, 3050 E, 3055 E, and 3065 E hold 12 liters. A 4-liter figure is typical of a smaller, lower-output engine cooling circuit, whereas 12 liters reflects a larger or more thermally demanding system.
  • The 3035 E and pre-Stage 5 3045 E share a change interval of 1000 hours or 12 months under normal use conditions, whichever comes first. A 12-month calendar limit alongside an hourly threshold accounts for seasonal or low-usage operation where calendar aging of coolant becomes the limiting factor before hours accumulate.
  • All Stage 5 variants introduced from 2024 onward carry a change interval of 2000 hours or 24 months under normal use conditions. Compared to the 1000-hour/12-month interval on earlier models, this represents a doubling of both the hourly and calendar thresholds, consistent with modern extended-life coolant formulations commonly specified for Stage 5 emissions-compliant engines.
  • The pre-Stage 5 3065 E, with a starting year of 2014, specifies a coolant level check every 10 hours in addition to a change interval of 1200 hours or 24 months. A 10-hour check interval is notably frequent and indicates a routine visual or dipstick-type inspection rather than a fluid exchange, serving as an early warning against leaks or consumption in a larger-capacity system.
  • The pre-Stage 5 3065 E has a change interval of 1200 hours or 24 months, which sits between the 1000-hour/12-month interval of the smaller 3035 E and 3045 E models and the 2000-hour/24-month interval of the Stage 5 variants. The 24-month calendar limit is shared with the Stage 5 models, while the hourly threshold remains lower.
  • The Stage 5 3045 E is identified by the serial number threshold NNZMW002V0BD50001, the 3050 E by NNZMW102V0BD50001, and both the 3055 E and 3065 E Stage 5 variants by NNZMW202V0BD50001. Serial number cutoffs of this kind are used to distinguish emissions-tier or specification changes within a model designation when the model name alone does not differentiate the variant.
  • The 3050 E appears only as a Stage 5 variant with a 2024 starting year, carrying the 12-liter capacity and 2000-hour/24-month change interval. No earlier non-Stage 5 specification is listed for the 3050 E, in contrast to the 3045 E and 3065 E, which each have both a pre-Stage 5 and a Stage 5 entry with differing capacities or intervals.

Other Systems