Deutz-Fahr 5600

Brake fluid capacity & service interval

Deutz-Fahr 5600 uses brake fluid with a capacity of 0,3 liter. Service intervals include a check every 10 hours and a change every 24 months. The data covers 10 configurations.

The configuration chart below lists fill volumes and service intervals for each engine and trim variant.

TypeSpecifications
5650 HTS COM 3, ->13500 (2009-2014)
  • Use: Normal
  • Capacity 0,3 liter
  • Change 24 months
5660 HTS Climber, ->13900 (2009-2014)
  • Use: Normal
  • Capacity 0,3 liter
  • Change 24 months
5660 HTS COM 3, ->13900 (2009-2014)
  • Use: Normal
  • Capacity 0,3 liter
  • Change 24 months
5665 HTS COM 3, ->13900 (2009-2014)
  • Use: Normal
  • Capacity 0,3 liter
  • Change 24 months
5690 H COM 3, ->13900 (2009-2014)
  • Use: Normal
  • Capacity 0,3 liter
  • Change 24 months
5690 HTS COM 3, ->13900 (2009-2014)
  • Use: Normal
  • Capacity 0,3 liter
  • Change 24 months
5695 HTS COM 3, ->13900 (2009-2014)
  • Use: Normal
  • Capacity 0,3 liter
  • Change 24 months
5670 H/HTS (2000-2008)
  • Use: Normal
  • Capacity 0,3 liter
  • Check 10 hours
  • Change 24 months
5680 H/HTS (2000-2008)
  • Use: Normal
  • Capacity 0,3 liter
  • Check 10 hours
  • Change 24 months
5690 H/HTS (2000-2008)
  • Use: Normal
  • Capacity 0,3 liter
  • Check 10 hours
  • Change 24 months

Additional Notes

  • Across all listed Deutz-Fahr 5600 series configurations, the hydraulic brake system fluid capacity is uniformly 0.3 liter. A value this small is consistent with a dedicated brake fluid reservoir rather than a shared or integrated hydraulic circuit, where capacities are typically measured in multiple liters.
  • The 24-month change interval applies to all configurations under normal use conditions, spanning both the 2000-2008 and 2009-2014 model year groups. Time-based brake fluid intervals exist because brake fluid is hygroscopic, meaning it absorbs moisture from the atmosphere over time, which lowers its boiling point regardless of operating hours.
  • The 2000-2008 H and HTS variants, specifically the 5670 H/HTS, 5680 H/HTS, and 5690 H/HTS, carry an additional 10-hour check interval not present in the 2009-2014 COM 3 specifications. A 10-hour interval corresponds to very early service life in agricultural equipment, where initial checks are used to confirm fluid level stability after the system has been put into regular operation.
  • The 2009-2014 COM 3 and Climber variants, including the 5650, 5660, 5665, 5690, and 5695 HTS models, list only the 24-month change interval without a separate periodic check interval. The absence of the 10-hour check in these later configurations reflects a difference in service schedule structure between the two generation groups.
  • The serial number ceiling of 13500 applies exclusively to the 5650 HTS COM 3, while the 13900 ceiling applies to all other 2009-2014 COM 3 and Climber variants. Serial number boundaries in agricultural equipment specifications are used to define the exact production range to which a given service specification applies, since mechanical revisions within a model line can alter fluid requirements.
  • The 5660 HTS is represented by two distinct configurations within the 2009-2014 group: the COM 3 and the Climber. Both share identical brake fluid capacity and change interval values, indicating that the differing trim or chassis designation does not affect hydraulic brake system service requirements for that model.

Other Systems