Claas Torion

Brake fluid capacity & service interval

Claas Torion brake fluid capacity is 0,8 liter. Service intervals consist of a check every 50 hours. The data covers 8 configurations.

The configuration chart below lists fill volumes and service intervals for each engine and trim variant.

TypeSpecifications
Torion 738 T Sinus Stage V, K60 (00011-) (2020- )
  • Use: Normal
  • Capacity 0,8 liter
Torion 535 Stage V, K50 (00201-) (2019- )
  • Use: Normal
  • Capacity 0,8 liter
Torion 639 Stage V, K52 (00201-) (2019- )
  • Use: Normal
  • Capacity 0,8 liter
Torion 537 Sinus Stage V, K51 (00011-) (2018- )
  • Use: Normal
  • Capacity 0,8 liter
Torion 644 Sinus Stage V, K53 (00011-) (2018- )
  • Use: Normal
  • Capacity 0,8 liter
Torion 956 Sinus Stage IV / Tier 4f, K54 (00011-) (2018- )
  • Use: Normal
  • Capacity 0,8 liter
  • Check 50 hours
Torion 535 Stage IIIB / Tier 4f, K50 (00011-00200) (2017-2019)
  • Use: Normal
  • Capacity 0,8 liter
Torion 639 Stage IIIB / Tier 4f, K52 (00011-00200) (2017-2019)
  • Use: Normal
  • Capacity 0,8 liter

Additional Notes

  • Across all listed Claas Torion configurations, the hydraulic brake system capacity is 0.8 liter. This figure represents a service fill volume, reflecting the fluid held within the hydraulic brake circuit rather than a full system overhaul quantity.
  • The Torion 535 appears in two distinct serial number ranges tied to different emissions standards. The Stage IIIB / Tier 4f variant covers serial numbers 00011-00200 for 2017-2019, while the Stage V variant begins at serial number 00201 with a starting year of 2019. Both share the same 0.8 liter brake fluid capacity.
  • The Torion 639 follows the same serial number boundary pattern as the 535, with Stage IIIB / Tier 4f production spanning 00011-00200 across 2017-2019 and Stage V production beginning at 00201 from 2019 onward. The 0.8 liter capacity applies equally to both variants.
  • Stage IIIB and Tier 4f are equivalent emissions certification tiers used in different regulatory regions, European and North American respectively. The Torion 535 and 639 carry dual designations to reflect compliance across both markets within the same production run.
  • The Torion 537 Sinus and Torion 644 Sinus are Stage V only configurations, introduced from 2018 onward under serial series K51 and K53 respectively. Neither has a preceding lower-emissions variant listed in the specifications.
  • The Torion 738 T Sinus, serial series K60, carries a starting year of 2020, making it the most recent introduction among the listed models. The hydraulic brake system capacity of 0.8 liter is consistent with the rest of the Torion range.
  • The Torion 956 Sinus Stage IV / Tier 4f, serial series K54, is the only configuration in the specifications that includes a brake fluid check interval. A 50-hour check interval is specified alongside the 0.8 liter capacity, indicating a periodic inspection point separate from a full fluid change.
  • A 50-hour check interval on the Torion 956 Sinus corresponds to early operational hours, a period when hydraulic systems are commonly monitored for fluid level stability as components settle and seals fully seat under working pressure.

Other Systems