Audi Q2, SQ2, GA (EU)

Manual transmission fluid capacity & service interval

Audi Q2, SQ2, GA (EU) manual transmission fluid capacity ranges from 2,3 to 2,4 liters. Service intervals require a check every 24 months or 30000 km. The data covers 9 configurations.

The configuration chart below lists fill volumes and service intervals for each engine and trim variant.

TypeSpecifications
Q2 30 TFSI (81 kW) (2020- )
  • Use: Normal
  • Capacity 2,4 liter
  • Check 24 months/ 30000 km
  • Code: 0AJ (MQ200) 6/1
Q2 35 TDI (110 kW) (2020- )
  • Use: Normal
  • Capacity 2,4 liter
  • Code: 02Q (MQ350) 6/1
Q2 35 TDI (110 kW) (2019-2020)
  • Use: Normal
  • Capacity 2,4 liter
  • Code: 02Q (MQ350) 6/1
Q2 30 TFSI (85 kW) (2018-2020)
  • Use: Normal
  • Capacity 2,4 liter
  • Check 24 months/ 30000 km
  • Code: 0AJ (MQ200) 6/1
Q2 35 TFSI (110 kW) (2018- )
  • Use: Normal
  • Capacity 2,4 liter
  • Code: 02S (MQ250) 6/1
Q2 1.4 TFSI (110 kW) (2017-2018)
  • Use: Normal
  • Capacity 2,4 liter
  • Check 24 months/ 30000 km
  • Code: 02S (MQ250) 6/1
Q2 1.0 TFSI (85 kW) (2016-2018)
  • Use: Normal
  • Capacity 2,3 liter
  • Check 24 months/ 30000 km
  • Code: 0AJ (MQ200) 6/1
Q2 1.4 TFSI (110 kW) (2016-2017)
  • Use: Normal
  • Capacity 2,4 liter
  • Check 24 months/ 30000 km
  • Code: 02S (MQ250) 6/1
Q2 1.6 TDI (85 kW) (2016-2018)
  • Use: Normal
  • Capacity 2,4 liter
  • Code: 02S (MQ250) 6/1

Additional Notes

  • The Audi Q2 1.0 TFSI (85 kW) carries a manual transaxle fluid capacity of 2.3 liters, which is the only variant in the Q2 GA lineup to fall below the 2.4-liter figure shared by all other listed configurations. A lower transaxle capacity typically reflects a physically smaller gearbox unit matched to a lower-torque engine.
  • All remaining manual transaxle configurations across the Q2 GA range share a uniform 2.4-liter fluid capacity, covering petrol variants from 81 kW to 110 kW and diesel variants at 85 kW and 110 kW alike.
  • A transaxle capacity figure represents a service fill volume, meaning the amount of fluid required when refilling a unit already installed in the vehicle. Overhaul or bench-fill quantities are generally higher due to additional internal passages and cavities that drain completely only when the unit is fully disassembled.
  • The Q2 1.6 TDI (85 kW) covering 2016-2018 lists a 2.4-liter transaxle capacity without an accompanying fluid check interval, distinguishing it from petrol variants of the same era that carry a 24-month or 30,000 km inspection schedule under normal use conditions.
  • The Q2 35 TDI (110 kW) in both the 2019-2020 and 2020-onward entries, as well as the Q2 35 TFSI (110 kW) from 2018 onward, all list a 2.4-liter capacity without a stated check interval, a pattern consistent with the 1.6 TDI diesel entry from the earlier model years.
  • Among the configurations that do carry a check interval, the schedule is consistent at 24 months or 30,000 km under normal use conditions. The dual-format interval means whichever threshold is reached first triggers the inspection, a standard approach in time-and-distance service scheduling.
  • The Q2 1.4 TFSI (110 kW) appears across two separate year-band entries, 2016-2017 and 2017-2018, both specifying identical 2.4-liter capacity and 24-month or 30,000 km check intervals under normal use. The overlapping year of 2017 across both entries reflects a mid-production-year specification revision rather than a change in fluid requirements.
  • The Q2 30 TFSI (81 kW) introduced from 2020 onward retains the same 2.4-liter transaxle capacity and 24-month or 30,000 km check interval as the Q2 30 TFSI (85 kW) covering 2018-2020, despite the slight reduction in rated output between the two variants.

Other Systems